EPTZ_db_en_rev EPTZ – 1/4″ day / night outdoor. Speed dome camera Built-in protocols: Pelco-P / Pelco-D / EverFocus /. ED / ED View and Download EverFocus Eptz user manual online. EverFocus Speed Dome User Manual. Eptz Security Camera pdf manual download. EverFocus EPTZ Manual Online: Eptz/eptzi Overview, Introduction. EPTZ/EPTZI, An Intelligent High-speed Dome Camera Is Ready To.

Author: Yogal Nikor
Country: Gambia
Language: English (Spanish)
Genre: Environment
Published (Last): 9 May 2009
Pages: 100
PDF File Size: 4.97 Mb
ePub File Size: 14.56 Mb
ISBN: 567-6-43785-277-8
Downloads: 87756
Price: Free* [*Free Regsitration Required]
Uploader: Mazurg

Up to preset positions can be stored into memory.

An extension power line may be needed. The system will ask you to enter the tour number you would like to run, and starts the tour after pressing Enter. It can go to every preset position in 1 second. Auto Pan 0300 Two point auto pan: If you set the position number to 98, the dome will Display the zoom multiple.

The control-related setting that is address, communication protocol and transmission speed have to be set consistently with the control device such as a keyboard or a DVR.

Align the 3 bolt holes into the 3 housing bolt holes, and screw three M3 bolts with the attached small screw driver to fix the bulb. M3 screw x3 for bulb fixing 2. Eptzi Dome Camera Installation 7. Privacy Masking Privacy masking allows certain areas of the picture to be blocked from view for privacy or legal reasons.

White Balance function makes the shades of color more natural in different light conditions. Don’t show me this message again. The mentioned screws evverfocus used in the normal concrete surface.


Wptz can set the masking size and position in the private zone setup mode. Utilizing an industrial grade stepping motor, this camera introduces powerful PTZ operations including a 30x optical zoom, degrees of continuous pan and 16 preset positions. Connect the cable connectors to the nodes everficus the PCB board, and then fix the PCB board in the housing by screwing 4 bolts on it.

It is located on the PCB board of the evrefocus. Position Setting Focus on a preset position: The camera module on the mechanical part is very sensitive.

Other Operations Note 2: This ensures that a person or object passing directly beneath the dome remains displayed in the upright position.

Also See for Eptz Specifications – 1 page User manual – 39 pages. Alternatively, you could run the tour without entering MENU. Thread the cable through the hole in the wall mount bracket, and screw in 4 M8 nuts for mounting the bracket.

Pan setting dwell time of A pos or B pos. Screw the two bolts on the base, and then connect and fix the connection bus to the PCB board on the mechanical part. Thread the cable through the screw and the hole on the top of the housing, and tighten up the screw to fix the cable 4. WBC setting will affect the wide dynamic range, or other image performance. Remove the lens protection cover before installing the bulb.


The available control functions depend on different everffocus. Auto and fast focus increases the searching speed and precision. Set an alarm link: Installation should be handled by a qualified service agent and should comply with all local regulations. Disable the private zone masking. Enable a normal close alarm input. Artboard Artboard Artboard Artboard. This counter counts the operation hours. Press the number key, and then press Position Auto iris is enabled.


EverFocus Eptz3000 User Manual

In order to protect the bulb from dirt and scrape, please put on the gloves before installing the bulb Auto focus is enabled. Electronics flip, no mechanical flip is necessary.

Mark the center of the holes on the wall against the bracket holes.

The extension poles are available for the pole mount. Fix the housing on the ceiling with two clips, adjust the screws of clips to make the housing perfectly fit to the ceiling.

The camera module on the mechanical part is very sensitive. Camera Setup Menu 3. Press F1 to set an alarm link. Feb15, Table of Contents 1. The system will ask you to enter preset position numbers The positions need to be preset. Disable the title display. However, there is only one line on the line display, so using some ept keys to operate is necessary. The 3 cables are too short to be connected to a wrong connector when putting them back.