ECE R26 PDF

Regulation No 26 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of vehicles with. ECE R26 Regulation (03 Series, ) “The uniform regulations on vehicle chapter and section numbering betw een this standard and the ECE R ECE UNIFORM PROVISIONS CONCERNING THE APPROVAL OF: VEHICLES WITH REGARD TO THEIR EXTERNAL PROJECTIONS Incorporating.

Author: Zulujora Nesida
Country: Papua New Guinea
Language: English (Spanish)
Genre: Literature
Published (Last): 2 April 2008
Pages: 50
PDF File Size: 14.4 Mb
ePub File Size: 1.34 Mb
ISBN: 863-4-98456-555-6
Downloads: 72557
Price: Free* [*Free Regsitration Required]
Uploader: Moshura

Air intake and outlet flaps shall meet the requirements of Paragraphs 5. The basic number of wheel fixings, for example f26 holes, 5 holes and so on, shall not be changed.

Wheels, wheel nuts, hub caps and wheel discs. In other words, if a regulation is changed so that an approval granted under the new version is not equivalent to an approval granted under the previous version, a new series will be issued.

Grilles and Gaps 6. Application for approval of a vehicle type with regard to its external projections. Acceptance criteria The test shall be considered satisfactory if there is not any visible fracture penetrating through the wheel surface and if there is not any loss of inflation pressure within one minute of completing the test.

If a Party to the Agreement applying this Regulation withdraws an approval it has previously granted, it shall forthwith notify the other Contracting Parties applying this Regulation by means of a communication form conforming to the model in Annex 1 to this Regulation.

It shall confirm that the tested wheel eve the requirements.

  GORDON MARINO BASIC WRITINGS OF EXISTENTIALISM PDF

GAR | World Forum Regulations

Windows which move outwards from the external surface of the vehicle shall comply with the following provisions in all positions of use:. Wheel fixing The use of vehicle manufacturer’s replacement wheel fixing components is recommended. Uniform Provisions Concerning the Approval of: Of side direction indicator lamps, end outline marker lamps, front and rear position side ecce and parking lamps; 2.

The normal frequency of these verifications shall be once every two years. With the hood lowered, no examination shall be made of the vehicle inside an imaginary surface formed by the hood when in the raised position. That department may then.

– Transport – UNECE

The assembly instructions shall contain sufficient information to enable the approved components to be mounted on the vehicle in a manner that complies with the relevant provisions of Paragraphs 5. Conformity of production 9. The competent authority shall verify the t26 of satisfactory arrangements for ensuring effective control of conformity of production before type approval is granted.

It shall be expressed according to the prescription of one International Tyre and Rim Standards and includes at least:. Trade name or mark of the vehicle: With regard to the design, inset, rim designation wheel fixing PCD and spigot mounting diameter, correspond to that of an OE-wheel, but wheel contour, material and so on, may be different.

The test report shall contain the details and results of the tests carried out. UN R75 Motorcycle Tires. Figure 3 shows an example of the use of this procedure. It does not apply to exterior rear-view mirrors or to the ball of towing devices. In case of test on the spoke, that spoke is to be chosen where the bolt hole is closest. UN R41 Motorcycle Noise Motorcycle Noise Uniform Provisions Concerning the Approval of Motor Cycles with regard to Noise The proposal for the 04 series of amendments, adopted at the June Forum session, will be posted as Revision 2 to the regulation pursuant to the completion of administrative formalities.

  ASKERI VESAYET PDF

Periodically, the Secretariat will consolidate these amendments and corrigenda into a new revision i. Uniform provisions concerning the approval of motor vehicles and their components with regard to the safety- related performance of hydrogen-fuelled vehicles UN Regulation version of the HFCV Global Technical Regulation.

Agricultural vehicle couplings Mechanical coupling components for agricultural vehicles UN Regulation No. The type approval authority shall be supplied with a copy of following information which shall also be supplied to the consumer with the wheel.

Number of wheels to be tested. Characteristics of the separate technical unit: Magnesium alloy wheels 6. It usually consists of two major parts:.

Licenses and Certificates

The dimension of the projection of a component which is mounted on a convex surface may be determined either directly or by reference to a drawing of an appropriate section of this component in its installed condition. One for each impact position One for each impact position.

Lateral deflectors shall have a radius of curvature of at least 1mm on edges capable of being directed outwards.