DGABK datasheet, DGABK pdf, DGABK data sheet, datasheet, data sheet, pdf, Intersil, Quad SPST, CMOS Analog Switches. DGABK Datasheet, DGABK PDF, DGABK Data sheet, DGABK manual, DGABK pdf, DGABK, datenblatt, Electronics DGABK. DGABK datasheet, DGABK circuit, DGABK data sheet: MAXIM – Quad SPST CMOS Analog Switches,alldatasheet, datasheet, Datasheet search site.

Author: Shakajind Vushicage
Country: Canada
Language: English (Spanish)
Genre: Love
Published (Last): 2 October 2017
Pages: 315
PDF File Size: 19.85 Mb
ePub File Size: 17.4 Mb
ISBN: 119-2-33456-624-4
Downloads: 69053
Price: Free* [*Free Regsitration Required]
Uploader: Shajora

Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. No circuit patent licenses are implied. Limit diode current to maximum current ratings. Asa cum sunt, la Tine vin!

In the OFF state each channel blocks voltages up to the supply rails. Dimension M applies to lead plating and finish thickness. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Device mounted with all leads soldered to PC board.

This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Package Information continued The package drawing s in this data sheet may not reflect the most current specifications. Maxim reserves the right to change the circuitry and specifications without notice at any time.

For this configuration dimension b3 replaces dimension b2. Pin Configurations continued To provide protection for overvoltages up to 20V above the supplies, a 1N or 1N type diode should be placed in series with the positive and negative supplies as shown in Figure 2.


DGA Intersil Quad SPST, CMOS Analog Switches ChipFind Datasheet Archive |

The algebraic convention whereby the most negative value is a minimum, and the most positive value is a maximum, is used in this data sheet. The addition of these diodes will reduce the analog signal range to 1V below the positive supply and 1V above the negative supply. For more information on TYP values see Note 3.

B1 maximum dimensions do not include dambar protrusions. When the enable input is high, a channel is selected by the address inputs, and when low, all channels are off. These devices are sensitive to electrostatic discharge; dg201abm proper IC Handling Procedures. VO is the steady state output with switch on.

DGABK (Intersil) – Quad SPST, CMOS Analog Switches, Analog Switches/Multiplexers

D, D1, and E1 dimensions do not include mold flash or protrusions. For more information on TYP values see Note 2. This dimension allows for off-center lid, meniscus, and glass overrun. Dimension Q shall be measured from the seating plane to the base plane.

Mold flash or protrusions shall not exceed 0. Maxim guarantees that these switches will not latch up if the power supplies are disconnected with input signals still connected. The DG has a maximum turn-off time of ns and a maximum turn-on time of ns. Putere n-am, Tu-mi fii sprijin. E and eA are measured with the leads constrained to be perpendicular to datum -C. Parameter guaranteed by design or characterization.


N is the maximum number of terminal positions.

DG201A/DG211 Quad SPST CMOS Analog Switches

These are stress ratings only, and functional operation dataxheet the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied.

The maximum limits of lead dimensions b and c or M shall be measured at the centroid of the finished lead surfaces, when solder dip or tin plate lead finish is applied. An enable input is provided.

In case of conflict between English and Metric dimensions, the inch dimensions control. Copyright Intersil Americas Inc.

The DGA has a maximum turn-off time of ns and a maximum turn-on time of ns.

However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. Lab 6 in this note. For the latest package outline information, go to www.

Datasheet «DG201A»

In either case, source-to-body diodes can be forward biased and conduct current from the signal source. Dambar protrusions shall not exceed 0. Measure dimension S1 at all four corners. Dimensions b1 and c1 apply to lead base metal only. All Rights Reserved All other trademarks mentioned are the property of their respective owners. For information regarding Intersil Corporation and its products, see www. Documents Flashcards Grammar checker.