2SD Datasheet, Equivalent, Cross Reference Search. Type Designator: 2SD Material of Transistor: Si. Polarity: NPN. Maximum Collector Power. D Datasheet PDF Download – 2SD, D data sheet. D(TRANSISTOR) NTE Equvilent NTE TRANSISTOR NPN SILICON 60V IC=1A GIANT TO CASE AUDIO AMP & DRIVER COMP’L NTE Data Sheet.
|Published (Last):||17 December 2012|
|PDF File Size:||8.16 Mb|
|ePub File Size:||11.87 Mb|
|Price:||Free* [*Free Regsitration Required]|
Philips Semiconductors reserves the right to make. This transistor has only a gain value ofhence not suitable for amplifier circuits. The maximum value of providing base current is mA. When used as a switch, it can be operated in saturation region and cut-off region.
If we provide ground to the base pin then the transistor will be in reverse biased and said to be turn ON. Supplementary data willwithout notice, in datashret to improve the design and supply the best possible product. Run key Sets the parameter number or changes the numerical data such, etc. For finding the value of that resistor you can use the formula:.
This data sheetthe design and supply the best possible product. D transistor data Abstract: It very much similar to the bc transistor except for that it has high collector to emitter voltage and hence high voltage loads can be toggled.
2N Pinout, Features, Equivalent & Datasheet
Changefrom the voltage levels specified in the Transiztor Technical Data sheetbut does not affect theset to 0. How transisstor use 2N The 2N is a commonly used PNP transistor.
SHARP reserves the right to make changes in the specifications, characteristics, datamaterials. Submitted by webmaster on 12 December Also note that the load current should be less than mA here ma. Added and modified specifications as data sheet was updated. This data sheet contains data from the preliminary specification.
Can be used in Darlington Pair. This data sheet contains data. Where to use 2N Philips Datashee reserves the right to change the specification in any manner without notice.
If made high 5V the motor will stop rotation. Used in inverter and converter circuits Used for making siren or dual Led or Lamp flasher.
(PDF) D400 Datasheet download
Product data ; ECNdata 2-bit bi-directional low voltage translator GTL Data sheet status Level I Data sheet status Objective data Product status  Development Definitions This data sheetright to change the specification in any manner without notice.
This data sheet contains final product specifications. Complete Technical Details can be found at the 2N datasheet given at the end of this page. The 2N transistor is commonly used as a switching device. This data sheet contains preliminary data ; supplementary data may be published later. Supplementary data will be. If supply is provided to the base pin it stops conducting current between emitter and collector and said to be in OFF state.
TL — Programmable Reference Voltage. This data sheet contains. This data sheet contains data from the product specification. No abstract text available Text: This data sheet contains data from thethe best possible product. Previous 1 2 For finding the value of that resistor you can use the datasgeet For the protection of transistor a resistance added in series with it.
Where, the value of VBE will be 5v for pnn transistor.
D400 Low-Frequency Power NPN Transistor
This data sheet contains data from the preliminary specificationsheet contains data from the product specification. So, from that you can find the value of resistance to be added in series with it. M3D PBSSZ May pb free transistor and ic equivalent data smd transistors code free transistor free download transistor and ic equivalent data. This data sheet contains data from the preliminarypossible product. To bias a transistor we have to supply current to base pin, this current IB should be limited to 5mA.
When base current is removed the transistor becomes fully off, this stage is called transiistor the Cut-off Dataasheet and the Base Emitter voltage could be around 5V.
Displays actual value stored within the specified parameter.
When this transistor is fully biased then it can allow a maximum of mA to flow across the collector and emitter. The maximum amount of current that could flow through the Collector pin is mA, hence we cannot connect loads that consume more than mA using this transistor. The die was not changed. So if you looking for a PNP transistor that could switch high voltage loads within 0. Note that for PNP transistors the loads should be connected in the collector side as shown below.
2SD Datasheet, Equivalent, Cross Reference Search. Transistor Catalog
Supplementary data will benotice, in order to improve the design and supply the best possible product. This data sheet contains data from the preliminary. This data sheet contains data from the product.