ASTM D – Designation: D /D M – 06 Standard Test Methods for Shear Adhesion of. ASTM D/DM: Standard Test Methods for Shear Adhesion of Pressure- Sensitive Tapes. A summary of ASTM standards relating to pressure sensitive tape is attached. The shear test procedures are also harmonized: ASTM D and PSTC.
|Country:||Antigua & Barbuda|
|Published (Last):||10 June 2009|
|PDF File Size:||8.98 Mb|
|ePub File Size:||14.96 Mb|
|Price:||Free* [*Free Regsitration Required]|
The mass of the clamp or hook described in 5. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. You can download and open this file to your own computer but DRM prevents opening this file on another computer, including a networked server. Historical Version s – view previous versions of standard. Referenced Documents purchase separately The documents d36654 below are referenced within the subject standard but are not provided as part of the standard.
New panels should be cleaned before use as described in Conduct an analysis of the logarithm of the data to determine the desired descriptive or comparative statistics.
China Supplier ASTM D3654 Polymide Tape Lasting Adhesive Test Meter
The edges shall be separated by 12 6 0. Procedures E, F, and G may be used to determine the ability of a filament reinforced tape to hold when placed under constant asfm. The results are available.
A standard mass is attached to the free end of the tape aatm allowed to act for the speci? Other grades may be used, provided it is? Combining values from the two systems will result in non-conformance with the standard.
The assessment may be within a roll of tape, between rolls or production lots. Some computer programs for data analysis allow the use of right-censored data.
Strong conclusions about a speci? These censored data may have a time to termination rather than a time to failure. Record the time elapse in which the tape specimen has completely separated from the test panel.
Already Subscribed to this document. The assessment may be within a roll of tape, between rolls or production lots.
Only the sellers and buyers responsability is involved in case of dispute. The 24 mm [1 in. Need more than one copy? This may be used to compare the shear adhesion of a tape to a particular fiberboard surface or to compare the shear adhesion of a tape to a variety of fiberboard surfaces.
ASTM D/DM – 06() – Standard Test Methods for Shear Adhesion of Pressure-Sensitive Tapes
Take care in the choice of samples and when comparing results between fiberboard surfaces which aztm not be exactly the same. For Procedures A and H, substitute steel panel instead of?
Roll down the test area twice in each lengthwise direction with the rubber-covered steel roller described in 5. Standards Subsctiption may be the perfect solution. For Procedures F and G, substitute a? This standard is not included in any packages.
Subscription pricing is determined by: NOTE 1—The mm [0. Repeat for a total of three washes with this solvent. For procedures B, C, D, and G remove?
ASTM D | Rycobel
During storage, panels should be protected from damage or contamination. Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards. Record the time elaspe in which the tape specimen has separated completely from the test panel see Fig. Width of specimen for Procedures E, F, and G if other than 12 mm [0.
ASTM D shearing tester is for the test of lasting adhesive of pressure sensitive adhesive tapes, labels and f3654 interrelated products. Please first log in with a verified email before subscribing to alerts. For Procedures E, F, and G the amount of slippage in mm [in.
For Procedures A, E, and H three replicate specimens shall be averaged in accordance with Section 11 for astn test result. This standard is subject to revision at qstm time by the responsible technical committee and must be reviewed every?
The surfaces of similar fiberboards may exhibit considerable variation between mills, between batches from one mill, and within batches. Special isothermal box for scooters and motorcycles.