ASTM D1267 PDF

This standard is issued under the fixed designation D ; the number immediately 1 This test method is under the jurisdiction of ASTM Committee D02 on. ASTM D Standard Test Method for Gage Vapor Pressure of Liquefied Petroleum (LP) Gases (LP-Gas Method). VAPOR PRESSURE ASTM D TECHNICAL SPECIFICATIONS. VAPOR PRESSURE CYLINDER UPPER CHAMBER. Stainless steel upper chamber with .

Author: Tulabar Kigagore
Country: Luxembourg
Language: English (Spanish)
Genre: Education
Published (Last): 14 May 2010
Pages: 459
PDF File Size: 5.25 Mb
ePub File Size: 14.90 Mb
ISBN: 127-4-67534-435-1
Downloads: 77678
Price: Free* [*Free Regsitration Required]
Uploader: Dokazahn

Right-click to open the PDF in a new window or download it: This test method is used to determine the vapor pressure at Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Vapor Pressure of Petroleum Products Introduction Many problems involving hydrocarbon systems include a specification of some sort atsm vapor pressure measurement.

Koehler K11500 (1-opening type) Reid Vapor Pressure Cylinder

Air saturation of the sample is performed by vigorously shaking the container and returning it to the cooling bath. True Vapor Pressure F This property is similar to the Vapor Pressure calculation except that the flash calculation is performed at a aztm temperature of F. Comments on Vapor Pressure If True or Reid Vapor Pressure values are calculated for oils or its fractions, the c1267 pseudo-components atsm be modeled as accurately as possible with respect to the oil characterization data.

These properties are new to VMGSim and are labeled as: The standard method establishes that the analyzed mixture must be placed atm a sample container kept in a cooling bath at 32 F. The sample is similarly saturated with air at 32 F and the vapor pressure form the system is also read from a pressure-measuring device attached to the apparatus.

The objective of this article is to present and discuss the different types of vapor pressure calculations available in VMGSim along with describing their calculation procedures, ranges of validity and units. Vapor Pressure, also known as bubble point pressure and true vapor astn, is the pressure where the first bubble of vapor is formed at a given temperature. The ASTM Da method establishes that the Reid Vapor Pressure is read from a pressure-measuring device that is attached to an ambient air filled chamber.

  IBALL SMPS CIRCUIT DIAGRAM PDF

Available request a quote.

Product Description The K Reid Vapor Pressure Cylinders are polished stainless steel test cylinders for vapor pressure tests of liquid petroleum products, volatile crude oil and liquefied petroleum gas LPG. Units Like in the Da method, there is confusion about the units used for this property. Link to Active This link will always route to the current Active version of the standard. Note that Nitrogen and Oxygen were added to the component list in order to be able to perform air saturation in the sample.

The following table shows the comparison of those values with those calculated from VMGSim:. Historical Version s – view previous versions of standard. Now, the RVPE is obtained through a new property as shown below. Conforms to the specifications of: Home Client Login Register. General Use laboratory apparatus balances, baths, blenders, centrifuges, chart recorders, freezers, fume hoods, furnaces, glassware washers, glove boxes, mixers, moisture testing, ovens, pumps, shakers, vacuum equipment, water purification VMGSim reports accurate results that are within, or close to, the reported uncertainty.

This test method covers the Reid Vapor Pressure determination of gasoline, volatile crude oils, and other volatile petroleum products. The vapor pressure of a mixture is commonly defined as the pressure where the first bubble of vapor is formed at a given temperature but there are other definitions based on standardized experimental measurements or correlations. Previous calculations in VMGSim did not take into account the air saturation, which caused the results to be asttm.

It is the responsibility astk the user of this asfm to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Subscribe to our technical newsletter. If True or Reid Vapor Pressure values are calculated for oils or its fractions, the oil pseudo-components should be modeled as accurately as possible with respect to the oil characterization data.

The precision for crude oil has not been determined since the early s see Note 3.

MINIVAP ON-LINE Process RVP Analyzer

Once this was done, a close match between calculated and experimental values of the distillation curve was obtained. Consists of upper chamber and lower chamber in required 4: VMGSim calculates the vapor pressure by flashing the mixture of interest using a vapor fraction equal to zero at the temperature specified in the stream that contains the mixture. It is also a useful parameter for the estimation of losses from storage tanks during filling or draining.

  AMURGUL GANDURILOR EMIL CIORAN PDF

The ASTM D method [1] covers the experimental procedure to obtain the vapor pressure of crude oils. If N 2 and O 2 are not present in the component list the calculation is done without the saturation part.

Petroleum Products and Biofuel lab apparatus baths, calorimeters, color measurement, density meters, flash point, hydrogenators, oil testing, penetrometers, surface tension, vapor pressure, viscometers and rheometers, This property is similar to the Vapor Pressure calculation except that the flash calculation is performed at a specific temperature of F.

Like in the Da method, there is confusion about the units used for this property.

Seta Reid Vapour Pressure Bath

Test Method D has been approved as a method for determination of vapor pressure of crude oil. The values given in parentheses are for information only.

The following link provides additional information from the instruction manual or original manufacturer’s brochure. ASTM Method being used? Validation examples are wstm included. Request prices on the required pressure gauges, thermometer, sample transfer connection and manometer.

Reid Vapor Pressure Bath – Koehler Instrument Company, Inc.

Maximum vapor pressure limits for gasoline are legally mandated in some areas as a measure of air pollution control.

The Reid Vapor Pressure is an important property of gasolines and jet fuels and it is used as a criterion for blending of products. Email Us or call toll-free: Units The Vapor Pressure is reported in absolute pressure units.

This property is calculated based on an equation presented in the EPA publication, derived from a nomogram first published by the American Petroleum Institute APIwhich is based d126 the Reid Vapor Pressure Equivalent of non — pressurized vessels see definition below and the storage temperature.

Units The Vapor Pressure F is reported in absolute pressure units. The calculation of the oil pseudo-components physical properties is very important since they define the computation of fugacities and equilibrium ratios that are part of the flash calculations used in r1267 pressure determination.