ASTM A666-10 PDF

ASTM A – Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. This standard is a part of ASTM. ASTM A March 10, Standard Specification for Annealed or Cold- Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar. This specification. ASTM A – Designation: A – 10 Standard Speci?cation for Annealed or Cold-Worked Austenitic.

Author: Zudal Vudoran
Country: Montserrat
Language: English (Spanish)
Genre: Love
Published (Last): 18 February 2004
Pages: 492
PDF File Size: 2.54 Mb
ePub File Size: 3.58 Mb
ISBN: 847-5-13325-145-4
Downloads: 79547
Price: Free* [*Free Regsitration Required]
Uploader: Bajar

Heat to o F to o F and cool at sufficiently high rates through oF to oF to avoid precipitation of chromium carbides.

Rockwell B 95 95 This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

Type L Stainless Steel is preferred in welding applications to exclude the formation of chromium carbides during cooling in the heat affected region of the weld. A — 10 Standard Speci?

The values given in parentheses are for information only. In case of dispute, the offset method of determining yield strength shall be used.

HardC Elongation in 2 in. Types and L cannot be hardened by thermal treatment. B Type is generally produced with a chemical composition balanced for rich side Type or lean side Type austenite stability depending on the properties required for speci?

One bend test shall be made from one end of each coil. Type L should be used in heavier sections to reduce the occurrence of carbide precipitation in the heat affected region adjacent to the weld pool Corrosion: Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

  KARL RAHNER GRUNDKURS DES GLAUBENS PDF

These alloys represent an excellent combination of corrosion resistance and fabricability. Current edition approved Sept. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. Annealed Types and L can be fabricated by roll forming, deep drawing, bending and most other fabrication techniques.

Type L LN The values obtained in this manner should not, however, be taken as the actual yield strength for 0. Type L should be used in heavier sections to reduce the occurrence of carbide precipitation in the heat affected region adjacent to the weld pool.

304 and 304L Stainless Steel

The choice of test method for materials in conditions other than annealed shall be at the option of the seller. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

Find wstm what NKS can do for you. Chemical equipment and piping, heat exchanger components, dairy and food handling equipment and utensils, cryogenic vessels and components, architectural and structural applications exposed to non-marine atmospheres.

Permission rights to photocopy the standard may also be secured from the ASTM website www. HRC typical L Ann 25 min. However, in the case of dispute, tests shall be made by pressure. Material Test Report and Certi? Hard Elongation in 2 in. C Annealed material that naturally meets mechanical properties may be applied.

and L Stainless Steel – NKS

This standard has been approved for use by agencies of the Department of Defense. Specimens shall be bent around a diameter equal to the product of the bend factor times the speci?

  ALGEBRA ABSTRACTA DE HERSTEIN PDF

Depending on the work hardening characteristics of the particular grade, either the yield or the tensile strength can be the controlling factor in meeting the properties. Originally approved in Maximum unless otherwise indicated. D PSS means plate, strip, sheet.

Chemical equipment and piping, heat exchanger components, dairy and food handling equipment and utensils, cryogenic vessels and components, architectural and structural applications exposed to non-marine atmospheres Aztm Composition: Number of Tests 8. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

Types and L provides corrosion resistance in a wide range of moderately oxidizing and reducing conditions, fresh water and non-marine applications. Only annealed conditions of grades speci? In the annealed condition it is essentially non-magnetic and becomes slightly magnetic with the application of cold work. Due to the high work hardening rate of these materials, intermediate anneals axtm required to successfully fabricate the part.

If asym metal is required, Type is normally used. Last previous edition approved in as A — This revision of Speci?

ASTM A for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar

The noncontrolling factor normally will exceed considerably the speci? A number in parentheses indicates the year of last reapproval. Types and L are weldable by most fusion or resistance welding techniques.